-- Network Working Group S. Kipp
-- Request for Comments: 4747 G. Ramkumar
-- Category: Standards Track McDATA Corporation
-- K. McCloghrie
-- Cisco Systems
-- November 2006-- The Virtual Fabrics MIBT11-FC-VIRTUAL-FABRIC-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,Unsigned32, mib-2
FROM SNMPv2-SMI -- [RFC2578]MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF -- [RFC2580]RowStatus,StorageTypeFROM SNMPv2-TC -- [RFC2579]
InterfaceIndexFROM IF-MIB -- [RFC2863]fcmInstanceIndex,FcNameIdOrZero,fcmPortEntry, fcmSwitchEntry
FROM FC-MGMT-MIB -- [RFC4044]T11FabricIndexFROM T11-TC-MIB;-- [RFC4439]t11FcVirtualFabricMIB MODULE-IDENTITYLAST-UPDATED"200611100000Z"ORGANIZATION"IETF IMSS (Internet and Management Support
for Storage) Working Group"CONTACT-INFO"
Scott Kipp
McDATA Corporation
Tel: +1 720 558-3452
E-mail: scott.kipp@mcdata.com
Postal: 4 McDATA Parkway
Broomfield, CO USA 80021
G D Ramkumar
SnapTell, Inc.
Tel: +1 650-326-7627
E-mail: gramkumar@stanfordalumni.org
Postal: 2741 Middlefield Rd, Suite 200
Palo Alto, CA USA 94306
Keith McCloghrie
Cisco Systems, Inc.
Tel: +1 408 526-5260
E-mail: kzm@cisco.com
Postal: 170 West Tasman Drive
San Jose, CA USA 95134
"DESCRIPTION"This module defines management information specific to
Fibre Channel Virtual Fabrics. A Virtual Fabric is a
Fabric composed of partitions of switches, links and
N_Ports with a single Fabric management domain, Fabric
Services and independence from other Virtual Fabrics.
Copyright (C) The IETF Trust (2006). This version of
this MIB module is part of RFC 4747; see the RFC itself for
full legal notices."REVISION"200611100000Z"DESCRIPTION"Initial version of this MIB module, published as RFC 4747."::={ mib-2 147}t11vfObjects OBJECTIDENTIFIER::={ t11FcVirtualFabricMIB 1}t11vfConformance OBJECTIDENTIFIER::={ t11FcVirtualFabricMIB 2}--********************************-- MIB object definitions--t11vfCoreSwitchTable OBJECT-TYPESYNTAXSEQUENCEOF T11vfCoreSwitchEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of core switches supported by the current
management entity."::={ t11vfObjects 1}t11vfCoreSwitchEntry OBJECT-TYPESYNTAX T11vfCoreSwitchEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry represents one core switch."INDEX{ fcmInstanceIndex, t11vfCoreSwitchSwitchName }::={ t11vfCoreSwitchTable 1}
T11vfCoreSwitchEntry ::=SEQUENCE{
t11vfCoreSwitchSwitchName FcNameIdOrZero,
t11vfCoreSwitchMaxSupported Unsigned32,
t11vfCoreSwitchStorageType StorageType}t11vfCoreSwitchSwitchName OBJECT-TYPESYNTAXFcNameIdOrZero(SIZE(8 | 16))MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The Core Switch_Name (WWN) of this Core Switch."::={ t11vfCoreSwitchEntry 1}t11vfCoreSwitchMaxSupported OBJECT-TYPESYNTAXUnsigned32(1..4095)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"In switches that do not support Virtual Fabrics,
this object has the value of 1. If Virtual Fabrics
are supported, this object is the maximum number of
Virtual Fabrics supported by the Core Switch. For
the purpose of this count, the Control VF_ID is
ignored."::={ t11vfCoreSwitchEntry 2}t11vfCoreSwitchStorageType OBJECT-TYPESYNTAXStorageType
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row."DEFVAL{ nonVolatile }::={ t11vfCoreSwitchEntry 3}-- Virtual Switch tablet11vfVirtualSwitchTable OBJECT-TYPESYNTAXSEQUENCEOF T11vfVirtualSwitchEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of Virtual Switches. When one Core Switch
provides switching functions for multiple Virtual Fabrics,
that Core Switch is modeled as containing multiple
Virtual Switches, one for each Virtual Fabric. This table
contains one row for every Virtual Switch on every Core
Switch. This table augments the basic switch information in
the fcmSwitchTable Table in the FC-MGMT-MIB."REFERENCE"fcmSwitchTable is defined in the FC-MGMT-MIB [RFC4044]."::={ t11vfObjects 2}t11vfVirtualSwitchEntry OBJECT-TYPESYNTAX T11vfVirtualSwitchEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry of the Virtual Switch table. Each row is for a
Virtual Switch.
This table augments the fcmSwitchTable, i.e., every entry
in this table has a one-to-one correspondence with an
entry in the fcmSwitchTable. At the time when the
fcmSwitchTable was defined, it applied to physical
switches. With the definition and usage of virtual
switches, fcmSwitchTable now applies to virtual switches
as well as physical switches, and (in contrast to physical
switches) it is appropriate to provide the capability for
virtual switches to be created via remote management
applications, e.g., via SNMP.
So, this entry contains a RowStatus object (to allow the
creation of a virtual switch), as well as a StorageType
object. Obviously, if a row is created/deleted in this
table, the corresponding row in the fcmSwitchTable will
be created/deleted."REFERENCE"fcmSwitchEntry is defined in the FC-MGMT-MIB module
[RFC4044]."AUGMENTS{ fcmSwitchEntry }::={ t11vfVirtualSwitchTable 1}
T11vfVirtualSwitchEntry ::=SEQUENCE{
t11vfVirtualSwitchVfId T11FabricIndex,
t11vfVirtualSwitchCoreSwitchName FcNameIdOrZero,
t11vfVirtualSwitchRowStatus RowStatus,
t11vfVirtualSwitchStorageType StorageType}t11vfVirtualSwitchVfId OBJECT-TYPESYNTAXT11FabricIndexMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The VF_ID of the Virtual Fabric for which this virtual
switch performs its switching function. The Control
VF_ID is implicitly enabled and is not set.
Communication with the Control VF_ID is required."REFERENCE"FC-SW-4, REV 7.5, section 12.2"::={ t11vfVirtualSwitchEntry 1}t11vfVirtualSwitchCoreSwitchName OBJECT-TYPESYNTAXFcNameIdOrZero(SIZE(8 | 16))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Core Switch_Name (WWN) of the Core Switch that
contains this Virtual Switch."REFERENCE"FC-SW-4, REV 7.5, section 12.2."::={ t11vfVirtualSwitchEntry 2}t11vfVirtualSwitchRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The status of this row."::={ t11vfVirtualSwitchEntry 3}t11vfVirtualSwitchStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row."DEFVAL{ nonVolatile }::={ t11vfVirtualSwitchEntry 4}-- Port tablet11vfPortTable OBJECT-TYPESYNTAXSEQUENCEOF T11vfPortEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of Port attributes related to Virtual Fabrics."::={ t11vfObjects 3}t11vfPortEntry OBJECT-TYPESYNTAX T11vfPortEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry represents a physical Port on a switch.
Switches that support Virtual Fabrics would add
these four additional columns to the fcmPortEntry
row."REFERENCE"fcmPortEntry is defined in the FC-MGMT-MIB module."AUGMENTS{ fcmPortEntry }::={ t11vfPortTable 1}
T11vfPortEntry ::=SEQUENCE{
t11vfPortVfId T11FabricIndex,
t11vfPortTaggingAdminStatus INTEGER,
t11vfPortTaggingOperStatus INTEGER,
t11vfPortStorageType StorageType
}t11vfPortVfId OBJECT-TYPESYNTAXT11FabricIndexMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The Port VF_ID assigned to this Port. The Port VF_ID is the
default Virtual Fabric that is assigned to untagged frames
arriving at this Port. The Control VF_ID is implicitly
enabled and is not set. Communication with the Control
VF_ID is required."REFERENCE"FC-SW-4, REV 7.5, section 12.1"DEFVAL{1}::={ t11vfPortEntry 1}t11vfPortTaggingAdminStatus OBJECT-TYPESYNTAXINTEGER{off(1),on(2),auto(3)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object is used to configure the administrative status
of Virtual Fabric tagging on this Port.
SET operation Description
-------------- -------------------------------------------
off(1) To disable Virtual Fabric tagging on this
Port.
on(2) To enable Virtual Fabric tagging on this
Port if the attached Port doesn't
prohibit it.
auto(3) To enable Virtual Fabric tagging if the
peer requests it."REFERENCE"FC-SW-4, REV 7.5, section 12.4"::={ t11vfPortEntry 2}t11vfPortTaggingOperStatus OBJECT-TYPESYNTAXINTEGER{off(1),on(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object is used to report the operational status of
Virtual Fabric tagging on this Port.
SET operation Description
-------------- -------------------------------------------
off(1) Virtual Fabric tagging is disabled on this
Port.
on(2) Virtual Fabric tagging is enabled on this
Port."REFERENCE"FC-SW-4, REV 7.5, section 12.4"::={ t11vfPortEntry 3}t11vfPortStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The storage type for this conceptual row, and for the
corresponding row in the augmented fcmPortTable.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row."
DEFVAL{ nonVolatile }::={ t11vfPortEntry 4}-- Locally Enabled Tablet11vfLocallyEnabledTable OBJECT-TYPESYNTAXSEQUENCEOF T11vfLocallyEnabledEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table for assigning and reporting operational status of
locally-enabled Virtual Fabric IDs to Ports. The set of
Virtual Fabrics operational on the Port is the bit-wise
'AND' of the set of locally-enabled VF_IDs of this Port
and the locally-enabled VF_IDs of the attached Port."::={ t11vfObjects 4}t11vfLocallyEnabledEntry OBJECT-TYPESYNTAX T11vfLocallyEnabledEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry for each locally-enabled VF_ID on
each Port."REFERENCE"FC-SW-4, REV 7.5, section 12.4"INDEX{ t11vfLocallyEnabledPortIfIndex, t11vfLocallyEnabledVfId }::={ t11vfLocallyEnabledTable 1}
T11vfLocallyEnabledEntry ::=SEQUENCE{
t11vfLocallyEnabledPortIfIndex InterfaceIndex,
t11vfLocallyEnabledVfId T11FabricIndex,
t11vfLocallyEnabledOperStatus INTEGER,
t11vfLocallyEnabledRowStatus RowStatus,
t11vfLocallyEnabledStorageType StorageType}t11vfLocallyEnabledPortIfIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The value of the ifIndex that identifies the Port."::={ t11vfLocallyEnabledEntry 1}t11vfLocallyEnabledVfId OBJECT-TYPESYNTAXT11FabricIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A locally-enabled VF_ID on this Port."::={ t11vfLocallyEnabledEntry 2}t11vfLocallyEnabledOperStatus OBJECT-TYPESYNTAXINTEGER{off(1),on(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object is used to report the operational status of
Virtual Fabric tagging on this Port.
SET operation Description
-------------- -------------------------------------------
off(1) Virtual Fabric tagging is disabled on this
Port.
on(2) Virtual Fabric tagging is enabled on this
Port."REFERENCE"FC-SW-4, REV 7.3, section 12.4"::={ t11vfLocallyEnabledEntry 3}t11vfLocallyEnabledRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The status of this conceptual row.
When a row in this table is in 'active(1)' state,
no object in that row can be modified except
t11vfLocallyEnabledRowStatus and
t11vfLocallyEnabledStorageType."::={ t11vfLocallyEnabledEntry 4}t11vfLocallyEnabledStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row."DEFVAL{ nonVolatile }::={ t11vfLocallyEnabledEntry 5}--********************************-- Conformance Section
--t11vfMIBCompliances OBJECTIDENTIFIER::={ t11vfConformance 1}t11vfMIBGroups OBJECTIDENTIFIER::={ t11vfConformance 2}t11vfMIBCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"Describes the requirements for compliance to the
Fibre Channel Virtual Fabric MIB."MODULE-- this moduleMANDATORY-GROUPS{ t11vfGeneralGroup }OBJECT t11vfCoreSwitchMaxSupported
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT t11vfCoreSwitchStorageType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT t11vfVirtualSwitchVfId
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT t11vfVirtualSwitchRowStatus
SYNTAXRowStatus{ active(1)}MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT t11vfVirtualSwitchStorageType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT t11vfPortVfId
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT t11vfPortTaggingAdminStatus
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT t11vfPortStorageType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT t11vfLocallyEnabledRowStatus
SYNTAXRowStatus{ active(1)}MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT t11vfLocallyEnabledStorageType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."::={ t11vfMIBCompliances 1}-- Units of conformancet11vfGeneralGroup OBJECT-GROUPOBJECTS{ t11vfCoreSwitchMaxSupported,
t11vfVirtualSwitchVfId,
t11vfVirtualSwitchCoreSwitchName,
t11vfVirtualSwitchRowStatus,
t11vfPortVfId,
t11vfPortTaggingAdminStatus,
t11vfLocallyEnabledOperStatus,
t11vfPortTaggingOperStatus,
t11vfLocallyEnabledRowStatus,
t11vfCoreSwitchStorageType,
t11vfVirtualSwitchStorageType,
t11vfPortStorageType,
t11vfLocallyEnabledStorageType
}STATUScurrentDESCRIPTION"A collection of objects for monitoring and
configuring Virtual Fabrics in a Fibre Channel switch."::={ t11vfMIBGroups 1}END